Listed here are typical installation directions for an ONAN 5500 Gas/Diesel/Propane having a generator wiring harness that is 8-pin.
Note: For action 7 you will have to buy 14-gauge electric cable for the run from our ShorePower track to your transfer switch.
STEP foreignwomen.com ONE:
Turn-off your generator AC circuit breakers to prevent interruption of coast energy solution during testing and installation of ShorePower track.
STEP TWO:
Recognize the following 4 cables on the generator wiring harness.
Work with a tape or label to mark each cable and that means you won’t forget which wire is which.
- A – Ground – Brown
- B – Stop – Green
- C – Begin – Red
- E – Run – Orange
The wires are labeled on the harness as follows on a typical ONAN 10-pin wiring harness
- A – Ground
- C – Start
- E – Stop
- F – Run
NOTE: The pin connections above are typical ONAN connections. Only a few ONAN generators have actually the generator that is same harness connections as some might have been changed because of the dealer or RV manufacturer. Make sure you have actually correctly identified the 4 cables properly before proceeding with step three.
STEP THREE:
Connect one Posi-Tap to every for the 4 cables identified in step two.
STEP 4:
Result in the connection through the ShorePower track towards the Posi-Taps (wiring harness) depending on the wiring diagram supplied.
- Green cable to E AVOID
- Red cable to C BEGIN
- Brown cable to A GROUND
- Orange cable to FRUN
Remember to link the proper cables to the wiring harness once we utilize red-colored cables more often than once.
On our installation picture we utilized wires that are white expand into the harness as a result of location of our product. The closer the installation of y our unit to your wiring harness will help you to make use of the supplied wire that is 4-foot we offer.
STEP 5:
- Link the wire that is red the ShorePower Monitor (I3) to at least one part associated with the enable switch utilising the provided Posi-Lock or perhaps a crimp connector.
- Connect the 2nd red cable (supplied in the zip-lock case) to another region of the switch that is enable. One other end of the wire that is red fundamentally get in touch to your good battery pack terminal.
ACTION 6:
- Connect the red wire through the enable switch therefore the red cable from (L+) from the ShorePower track to your +12 VDC (good battery terminal).
- Link the wire that is blackM) in the ShorePower track to ground (any steel in your RV).
ACTION 7:
Through the ShorePower Monitor Power Converter ( See wiring diagram B – Transfer Switch Connection):
You need 14-gauge stranded electrical cable for the run from our device to your transfer switch.
- Connect (L) on our MeanWell Power Converter to 1 part associated with the 110 Volts regarding the transfer switch.
- Link the (N) on our MeanWell Power Converter into the center connection (common) in the transfer switch
ACTION 8:
The ShorePower track & the MeanWell Power Converter should both have their green light in, if all of the wires, such as the cables to your transfer switch, are properly linked. .
- To check the machine turn the ENABLE Switch ON and disconnect from coast energy. The green light on the MeanWell is certainly going down and in about 20 moments our product will auto-start your generator.
- Let generator run for approximately a moment then re-connect to shore energy and our device will immediately shut-off your generator in more or less seconds that are 10-12. The light that is green the MeanWell should come straight right back on.
ESSENTIAL NOTE: switching the ALLOW CHANGE On or OFF doesn’t impact the light that is green the ShorePower track or MeanWell. In the event that ShorePower track is correctly link along with coast power those two light will be on. The ALLOW CHANGE just allows or disables monitoring.
It’s this that a set-up that is typical seem like once it is completed. You will see other client installation photos by clicking right right here.